“Assemble to Order” means you can choose a basic pump with gas, air or electric motor. Then select the proper valve, gauge, pressure control, motor control and reservoir. You get a two-stage pump that gives high oil volume for fast cylinder approach (and return with double- acting cylinders) in the first stage and high pressure in the second stage.

These motors start under full load and are suitable for operation up to 5,000 or 10,000 psi. The motor is 11⁄8 hp, 12,000 rpm, 115 or 230 volt (specify), 50/60 cycle A.C. single phase (25 amp draw at 115V.). With proper valve they can be used with single- or double-acting cylinders. Remote control available.

Feature low noise level, moderate speed for long service and are ideal for fixed applications. Motor is 11⁄2 hp, 3,450 rpm, 115 or 230 volt, 50 or 60 cycle (specify), A.C. single phase with thermal overload switch. Can be used with single- or double-acting cylinders and equipped with remote control. Also available in 230/460 volt, three-phase (specify).

NOTE: These do not start under full load unless valve is in “neutral” (requires open or tandem center valve) and are not recommended for frequent starting and stopping.

Gives low noise level and long life due to its moderate operating speed. Ideal for fixed installations. Consists of basic 10,000 psi pump, jet pump motor: 3 hp, 3,450 rpm, 230/460 volt, 60 or 50 cycle (specify). A.C. threephase, with thermal overload switch. Equipped with internal and external relief valve. Will start under load.

This pump is ideal for use where electricity is unavailable or cannot be used. The 5,000 or 10,000 psi pump has a 3 hp air driven motor at 3,000 rpm (optimum performance based on 80 psi air pressure and 50 cfm at the pump). You can drive single- or double- acting cylinders with the correct valve.

NOTE: 80 psi air supply required to start under full load.

This version is perfect when electricity and air are unavailable. It is capable of continuous operation at full pressure. Consists of basic 10,000 psi pump, 4-cycle Briggs & Stratton “Diamond Edge” gasoline engine, developing 6 hp. As with all these pumps, this unit can be valved for use with either single- or doubleacting cylinders.

You can choose from pre-engineered, off-the-shelf components to customized your pump. All the components are listed in table form, with key letters or numbers in 'Specifications'. Complete instructions guide you so you can determine what is needed to complete a pump assembly. Shown below is an example of a custom-built pump.

Pump No. PE55A-VV-Z-G-A-A-A-A-D-BB-C-2F is a 10,000 psi two-speed pump with a 115 volt, 50-60Hz, single phase, 1 1/2 hp, 12,000 rpm motor; a 9512 4-way solenoid valve with a 202778 remote hand control, a 9041 pressure gauge, no gauge accessories, standard pressure control, standard On-Off-Pulse motor control, 400630OR9 2-gallon reservoir, a 350431 fluid level/temperature gauge, 10494 casters, and 2 gallons of standard hydraulic oil.

TO BUILD YOUR PUMP, FILL IN KEY LETTERS FROM CHARTS

Use the charts numered from 1-12 below to select the pump, valve, gauge and other accessories to suit your needs. For the pump, fill in the basic number plus key letter in block 1 above and the key letter only in the blocks 2-12 above for any of the other items. Refer to the appropriate web pages for more specific information on the products you need.

Go to Accessories section for product detail:

Hydraulic Pump Accessories:On/Off Motor Control, Remote Air Motor Controls, Subplates, Pump Mounted Subplates, Air Filter/Regulator/Lubricator, Pressure Switch, Pilot Operated Air Control Valves, Foot Control Guard, and Magnetic Strip.